> For the complete documentation index, see [llms.txt](https://biscuitsecurity.gitbook.io/introduction/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://biscuitsecurity.gitbook.io/introduction/learn-iot-pentesting-bug-bounty/iot-pentesting-tools.md).

# IoT Pentesting Tools

Baseline hardware for IoT / embedded bug bounty and pentesting. Grouped by workflow stage.

***

## 1. Target & Basic Bench Tools

### WiFi Router (practice target)

Cheap consumer router used as a first hardware target. Ideal for learning the full chain: teardown → UART → bootloader → firmware extraction → filesystem analysis.

**IoT use:** Safe practice device for locating UART pads, getting a root shell, and dumping firmware before moving to bounty targets.

### iFixit Toolkit

Precision screwdriver set with pry tools, spudgers, and tweezers.

**IoT use:** Non-destructive enclosure opening (clips, security bits, glued shells) to access the PCB without damaging the device or voiding a working test unit.

### Multimeter

Measures voltage, continuity, and resistance.

**IoT use:** Identify GND/VCC/TX/RX pads on UART headers, verify logic level (3.3V vs 5V) before connecting an adapter, and trace connections between test points and chip pins.

### Jumper Wires

Male/female Dupont wires for temporary connections.

**IoT use:** Connect UART adapters, logic analyzers, and SPI/I2C programmers to header pins or test pads without soldering.

### Power Supply (bench / adjustable)

Adjustable DC supply with current display.

**IoT use:** Power devices independently with a controlled voltage, monitor current draw during boot, and safely power-cycle targets during fault injection or boot-timing tests.

***

## 2. Debug Interface & Bus Analysis

### USB-to-3.3V UART Adapter

Serial adapter (FT232/CP2102/CH340-based) exposing TX/RX/GND at 3.3V.

**IoT use:** Access the serial console for boot logs, U-Boot interrupt, and often an unauthenticated root shell. Usually the fastest win on IoT devices.

### Logic Analyzer

Captures and decodes digital signals (UART, SPI, I2C, JTAG).

**IoT use:** Determine unknown baud rates, sniff SPI flash traffic, identify JTAG/SWD pinouts, and capture inter-chip communication for protocol analysis.

### Oscilloscope

Displays analog signal waveforms over time.

**IoT use:** Inspect signal integrity, verify voltage levels and glitches, and support power analysis / voltage-glitching attacks to bypass secure boot or debug locks.

### Raspberry Pi Pico

Low-cost RP2040 microcontroller board.

**IoT use:** Flexible attack tool: JTAG/SWD probe (Picoprobe), SPI flash reader, UART bridge, or a glitching platform (e.g. voltage/clock glitching with custom firmware).

***

## 3. Firmware Extraction

### XGecu Universal Programmer (T48 / TL866-series)

Programmer supporting thousands of flash/EEPROM/MCU chips, with SOIC/ZIF adapters.

**IoT use:** Read or write SPI/NAND/NOR flash directly (in-circuit or desoldered) to dump full firmware, bypassing bootloader restrictions. Also used to flash modified firmware for backdoor/persistence testing.

***

## 4. Soldering & Rework

### Soldering Iron (e.g. Pinecil)

Portable USB-C / DC powered iron with temperature control.

**IoT use:** Solder headers onto UART/JTAG pads and attach wires to test points for stable, repeatable access.

### Soldering Station

Bench station with stable temperature control.

**IoT use:** Higher-power, consistent heating for ground planes, large pads, and thicker headers where portable irons struggle.

### Microsoldering Pencil + Tips

Fine-tip pencil with interchangeable micro tips.

**IoT use:** Solder to small test pads, fine-pitch chip legs, and 0402/0201 components. Needed for wiring directly to flash chip pins for in-circuit reads.

### Solder

Leaded or lead-free solder wire (thin gauge, flux-core).

**IoT use:** Making reliable joints on headers and test points. Thin (0.3–0.5mm) wire is best for fine-pitch work.

### Wire Strippers

Precision strippers for small-gauge wire.

**IoT use:** Prepare thin wires for soldering to test pads and chip pins without nicking strands.

### Hot Air Rework Station

Temperature/airflow-controlled hot air gun.

**IoT use:** Desolder eMMC/NAND/SPI flash chips for off-board dumping (chip-off), or remove protective components and shields to expose test points.

### Air Extraction (fume extractor)

Filters solder and flux fumes.

**IoT use:** Health/safety during long soldering and rework sessions. Not attack-related, but essential for a hardware bench.

***

## 5. Microscope Setup

### Microscope

Stereo/trinocular microscope for PCB inspection.

**IoT use:** Read chip markings, identify test pads, inspect solder joints, and verify fine-pitch soldering when working with tiny components.

### Microscope 0.7X Lens (auxiliary objective)

Lower magnification lens that increases working distance and field of view.

**IoT use:** More room under the lens to use iron, tweezers, and hot air while working on the board.

### Microscope LED Ring Light

Ring illumination mounted on the microscope objective.

**IoT use:** Even, shadow-free lighting to read etched/laser-marked chip text and spot tiny pads on dark PCBs.

### Microscope Camera

USB/HDMI camera attached to the microscope.

**IoT use:** Live-view on screen for comfortable soldering, plus capturing high-res board photos for documentation and bug bounty report PoCs.

***

## Suggested Minimum Starter Kit

| Goal                        | Tools                                                                           |
| --------------------------- | ------------------------------------------------------------------------------- |
| UART shell access           | iFixit toolkit, multimeter, UART adapter, jumper wires, soldering iron + solder |
| Firmware dump (in-circuit)  | Above + XGecu programmer, SOIC clip, logic analyzer                             |
| Chip-off / advanced         | Above + hot air station, microsoldering pencil, microscope                      |
| Fault injection / glitching | Oscilloscope, Raspberry Pi Pico, bench power supply                             |
